The torque settings are 40N.m (29.5ft.lb) + 120 degrees for the bigger M11 bolts which secure the main part of the head & 15 N.m (11.06 ft.lb) + 45 degrees for the 2 smaller bolts in the timing chain section. Procedure is as follows: 1) Starting with the middle pair of M11 bolts tighten to 30 N.m working outwards and criss-crossing as you go. Steering wheel bolt Torque specs? Maintenance, Warranty Issues & Troubleshooting: 2: Apr 26, 2018: Valve cover bolts torque specs needed: Maintenance, Warranty Issues & Troubleshooting: 6: Jul 7, 2017: Lower Chassis/Tie Brace. A-Arm Bolt Torque? Suspension, Brakes & Chassis: 6: Apr 1, 2017: stub axle bolt torque settings: Transmission 52-nm, 38lbf ft. Mondeo MK4 tdci Estate 09. B. b_kennedy Discussion starter. 91 posts · Joined 2009. #3 · Aug 1, 2009. Thanks mate your a Top dog (pun intended haha). Torque it straight to that or is there a quarter/half turn etc after, cheers.
37 ft-lbs. Timing Belt Tensioner Torque spec. 18 ft-lbs. Camshaft Sprockets Bolt Torque spec. 50 ft-lbs. Crankshaft Postition Sensor Torque spec. 15 ft-lbs. Camshaft Bearing Caps Torque spec. 15 ft-lbs.
Unit 7, Raymar Business Park, Axe Road, Bridgwater, Somerset, TA6 5LJ, UK +44 208 391 0121 - Monday to Friday: 09:00 – 17:30
3 answers. Tighten the cylinder head bolts in the sequence shown. Using the 4 step torque turn method, tighten according to the following values: Step 1: All to 34 Nm (25 ft. lbs.) Step 2: All to 68 Nm (50 ft. lbs.) Step 3: All to 68 Nm (50 ft. lbs.) CAUTION: Do not use a torque wrench for the following step.
What is the torque setting for the crank pulley on 1.6 Rocam bantam ? According to the Workshop Manual for a 2006 Ford Bantam 1.6L/1.3L RoCam the crankshaft pulley bolt is tightened to 125Nm Read full answer
Torque: 1: 85 lb.ft (115 Nm) 6x big bolts. 2: 18 lb.ft (25 Nm) 2x small bolts, exhaust hanger. --. From the looks of the rear subframe in this service manual, the design of the locating pins and are near identical to that of vehicles I've worked on in the past. As long as those pins are located, and you've got the bolts installed, the subframe
Dorman # Applications Torque Spec 594-102 1990-86 2.9L Ford Bronco 130 lbs 594-103 2000-90 3.3L Chrysler, Dodge, Plymouth 40 lbs 594-106 1999-94 2.0/2.4L Mitsubishi Eclipse, Galant 45 lbs Car. Ford Focus 1.6 TDCi. 12 December 2008. #4. exactly as others said, new air filter, then remap. if you want to do more you can de-cat it, and remove the DPF, then remap it again. If u want to go mental, bigger turbo, bigger intercooler. Then remap again to get the most out of it! P.
Chris. 19,858 satisfied customers. Need torque specifications for 2011 Range rover 5.0l engine. need torque specifications for 2011 Range rover 5.0l engine such as cylinder head bolts, camshaft sprocket bolts, crankshaft pulley bolt, … read more.
.
  • 63owgfzr5y.pages.dev/67
  • 63owgfzr5y.pages.dev/108
  • 63owgfzr5y.pages.dev/345
  • 63owgfzr5y.pages.dev/490
  • 63owgfzr5y.pages.dev/89
  • 63owgfzr5y.pages.dev/138
  • 63owgfzr5y.pages.dev/293
  • 63owgfzr5y.pages.dev/240

    • ford focus 1.6 torque settings